{"id":7379,"date":"2019-10-25T09:24:35","date_gmt":"2019-10-25T09:24:35","guid":{"rendered":"http:\/\/www.ifroglab.com\/en\/?p=7379"},"modified":"2019-10-26T14:29:21","modified_gmt":"2019-10-26T14:29:21","slug":"wsg309s-evb","status":"publish","type":"post","link":"https:\/\/www.ifroglab.com\/en\/?p=7379","title":{"rendered":"WSG309S EVB"},"content":{"rendered":"

WSG309S EVB\u00a0 \u00a0Introduction<\/b><\/p>\n

 <\/p>\n

This document describes how to use the SigFoxEvaluation Board (EVB), which is aguide-linefor engineers to develop and test LPWANmodules.<\/p>\n

This document is applicable to LITE-ON WSG309SEVB KIT.<\/p>\n

LITE-ON supplies LPWANEVB for designers to develop application based on LITE-ON SigFox module(LPWAN Module). Before you start usingit, here is something you need to prepare.<\/p>\n

1. WSG309SEVB<\/p>\n

2. USB Type A connectorfor power and data communication<\/p>\n

3. Serial COM port Tool<\/p>\n

4. PC or Notebook<\/p>\n

 <\/p>\n

 <\/p>\n

General Overview<\/b><\/p>\n

This Chapter shows the overview of EVB. The EVB can test basic functionalities of WSG309S .<\/p>\n

 <\/p>\n

EVB Top and Bottom view<\/b><\/p>\n

\"\"<\/p>\n

\"\" \"\" \"\" \"\" \"\" \"\"<\/p>\n

Interface Application<\/b><\/p>\n

The following tables show the I\/O parameters Definition of EVB.<\/p>\n

 <\/p>\n

 <\/p>\n

Power & Data Interface<\/b><\/p>\n

To insure the all the power interface would work fine, please checkthe USB is plugged before power on the EVB since the power is supplied by USB Type A interface.In the case of WSG309S, power source is supplied via main USB port.<\/p>\n

 <\/p>\n

Antenna Interface<\/b><\/p>\n

 <\/p>\n

 <\/p>\n

Switches and Buttons<\/b><\/p>\n

\"\"<\/p>\n

\"\"<\/p>\n

 <\/p>\n

I\/O Pins and Test Points<\/b><\/p>\n

\"\" \"\" \"\"<\/p>\n

 <\/p>\n

UART Interfaceand definition<\/b><\/p>\n

EVB has anonboard USB-to-Serial (UART) Bridge Controller, the external interface converter is not necessary. While the UART interface of WSG309Sis reserved for design purpose, it could be used to pre-development in early stage of product.The Pin definition is show as below:<\/p>\n

If you want to enable the UART function of pin header, please implement 2 jumpers with correct direction.<\/p>\n

 <\/p>\n

\"\" \"\"<\/p>\n

Operation Procedures Illustration<\/b><\/p>\n

 <\/p>\n

Power on the Module<\/b><\/p>\n

 <\/p>\n

1.Install the SigFoxAntenna.<\/p>\n

2.Plug-inthe USB port.TheD1 LEDon the EVB will be lightin green. And WSG309Smodule will be powered on (WSG309Smodule does not have PWRKEY pin).<\/p>\n

 <\/p>\n

 <\/p>\n

3.<\/p>\n

Let PC\/Laptop access the internet and wait for the driver installation of USB-to-Serial (UART) Bridge Controller. The driver would install automatically.<\/p>\n

4.<\/p>\n

To check the device manager if a new serial COM port is created.<\/p>\n

 <\/p>\n

 <\/p>\n

Communication via UARTinterface<\/b><\/p>\n

(1) Connect the main port of EVB to PC USB port.<\/p>\n

 <\/p>\n

 <\/p>\n

(2) Open the AT command toolsuch as HyperTerminal on PC. The location of the HyperTerminal in Windows XP system is Start\u2192<\/span>Program\u2192<\/span>Accessory\u2192<\/span>Communication\u2192<\/span>HyperTerminal. Or the other Serial COM port Toolfor operating is also applicable.<\/p>\n

\"\"<\/p>\n

(3) Set appropriate baud rate (115200bpsfor WSG309S) and COM number which can be checked by the Device Manager on PC.<\/p>\n

\"\"<\/p>\n

(4) Power on the module according to the procedures mentioned in Chapter 4.1.<\/p>\n

\"\"<\/p>\n

(5) Wait for 2~3 seconds, and input \u201cEnter or Help\u201d string once or more until \u201cMessage\u201d is received from the module in the HyperTerminal.<\/p>\n

\"\"<\/p>\n

 <\/p>\n

(6) Please refer to the document SigFox WSG309S_Module_Spec_V1.0and WSG309S_Monarch_AT_Command_20190402Data Communication User Guide or the AT Command Manualfor detail operation.<\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n","protected":false},"excerpt":{"rendered":"

WSG309S EVB\u00a0 \u00a0Introduction   This document describes how to use the SigFoxEvaluation Board (EVB), which is aguide-linefor engineers to develop and test LPWANmodules. This document is applicable to LITE-ON WSG309SEVB KIT. LITE-ON supplies LPWANEVB for designers to develop application based on LITE-ON SigFox module(LPWAN Module). Before you start usingit, here is something you need to […]<\/p>\n","protected":false},"author":1,"featured_media":7204,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[57],"tags":[],"class_list":["post-7379","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-sigfox"],"_links":{"self":[{"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/posts\/7379","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=7379"}],"version-history":[{"count":2,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/posts\/7379\/revisions"}],"predecessor-version":[{"id":7383,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/posts\/7379\/revisions\/7383"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=\/wp\/v2\/media\/7204"}],"wp:attachment":[{"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=7379"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=7379"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.ifroglab.com\/en\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=7379"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}