iForgLab LoRaWAN- Vegas series for full band SX1276

iForgLab LoRaWAN- Vegas series for full band SX1276

iFrogLab  Lora 137 – 1020 MHz(Full band supported)   SX1276 LoRa “Vegas  Series”  forLoRaWAN compatible

Features:

  • LoRa industrial controller 
  • Frequency Range: 137 – 1020 MHzMHz
  • Modulation: FSK/GFSK/MSK/LoRa
  • 168dB maximum link budget
  • Output Power: +20dBm Data Rate: <300 kbps 127dB dynamic Range RSSI Excellent blocking immunity Preamble detection Automatic RF sense and CAD monitor Built-in bit synchronizer for clock recovery Packet engine up to 256 bytes with CRC
  • Working Temperature: -40°C ~+80°C Build-in temperature sensor
  • RS232
  • RS485
  • Supply voltage: DC 5〜30V
  • Has Complete sample code for such LoRa gateway https://github.com/iFrogLab/IL-LORA1272

 

Features:

  1.  Made in Taiwan
  2. Supported open Standard LoRaWAN protocol. 
  3. Supported iForglab LoRa protocol
  4. Direct use of RS232/RS485  interface control, do not need to understand the complex transmission LORA concept.
  5. Implementation intelligent sensor (Worldwide only )
    • temperature
    • humidity
    • accelerometer
    • lux
  6.  Can be directly connected with the Raspberry Pi quick practice ioT LoRa gateway, do not need expensive LoRaWan gateway
  7.  iFroglab provides driver and can receive more than one LoRa module/Dongle multiplexing, the industry’s first.
  8.  The actual test can reach 3km away, the rapid completion of iOT remote control!
  9.  Ground floor, second floor of the launch information can be easily received on the sixth floor upstairs, you can directly replace the Zigbee and Zwave and other network technology!
  10.  The transmission of information through the wall through the ground.
  11.  To provide a complete raspberry and Arduino example of the program can be a simple data transmission and reception of the sample program https://github.com/iFrogLab/IL-LORA1272 and Sample program for LoRa gateway https://github.com/iFrogLab/
  12. Get started quickly
  13. can connection with LoRa gateway and easy to establish LoRa network.
  14. Supported iForglab utility that can sent data to Dashboard directly. don’t needs any complex configure

 Driver:

  • Windows driver from here 
  • Mac No driver required
  • Linux No driver required, you should check device name ,e.g. : /dev/ttyAMC0
  • QNAP NAS No driver required,you should check device name ,e.g.: /dev/ttyAMC0
  • Raspberry Pi No driver required,you should check device name ,e.g.: /dev/ttyAMC0
  • The New LoRa APP can validation for each platform of LoRa dongle,Here

iL-LORA1272 is a type of low cost RF front-end transceiver module based on SX1272 from Semtech Corporation. It keeps the advantages of RFIC SX1272 but simplifies the circuit design. The high sensitivity (-137dBm) in LoRa modulation and 20dBm high power output make the module suitable for low range and low data rate applications.

iL-LORA1272 module consists of RFIC SX1272 and include powerful MCU, thin SMD crystal and antenna matching circuit. The antenna port is well matched to standard 50 Ohm impedance. Users don’t need to spend time in RF circuit design and choose suitable antennas for different applications. iL-LORA1272 operates at 1.8~3.6V with extra low standby current which makes it suitable for battery powered-up applications. Because iL-LORA1272 is purely hardware module and it adopts ±10ppm crystal which the resolution of it places a important role in calculating spreading factor, bandwidth, etc.

In addition, We’er add powerful MCU to help Users that don’t needs to read the datasheet of SX1272, you just go through UART to control this module and will easy to use the module in the best performance.

 Document

PPT download here

UART data spec PDF here

Application Note Here

Source Code

github download

LoRa Gateway

Docker Container here

Tutorial  here

 

 

No Comments

Comments are closed.